Corovent CDV Continuous Dry Verge

Continuous Dry Verge Ridge End Cap Black

Continuous Dry Verge Ridge End Cap

Continuous Dry Verge End Caps are specially designed for use when installing the Corovent CDV on pitched roofs to create a neat attractive finish to the apex of the roof.

features

  • Single piece product
  • Dry fix mortar free solution
  • Manufactured from UV stabilised UPVC
  • 100% waterproof
  • Available in a choice of colour options

ideal for

Pitched roof projects

guidance

Full installation details are available on request from the Technical Department.

Fitting of Continuous Dry Verge - Tile Profile

  1. The Continuous Dry Verge should be cut to the required length, allowing for a plumb cut at the ridge, and approximately 150mm longer than the rafter. The horizontal flange is cut away, to allow fitting over the felt support tray at the eaves.
  2. The battens are placed against the lip of the water channel of the dry verge, which are then nailed into position directly through the horizontal fin of the verge. The nails are fixed through both batten and verge, into the timber rafter. A close-up of the roof battens in place show their position against the lip of the drainage channel. Once all the battens are fixed in place, and the Dry Verge secure, the roof is ready for tiling.
  3. The roof tiles are fitted in the usual manner, ensuring that the verge tiles are fully inserted into the verge, where the top flange will hold them firmly in place. At the eaves, the verge should be cut square, flush to the lower tile, and notched into the gutter. Eaves stop ends are available for closing the eaves on the 'R' and 'D' profiles. The water channel allows any rainwater to run directly into the rainwater gutter. 
  4. The fitted Continuous Dry Verge achieves a professional finish. This will be similar for any roof tile or slate being used. The completed roof gives complete continuous cover against water penetration, and added strength from wind damage by securing end tiles firmly. 

 

Fitting of Continuous Dry Verge - Slate Profile

  1. The roof battens are fixed in place to the required slate gauge, however, the batten ends are not fixed in place as yet, to allow the 60mm flange of the slate verge to be fitted under the batten, which is the easiest way to fit in place. 
  2. The roof battens ends are then securely fixed in place, by nailing through both batten and verge, into the timber rafter. The slate verge profile is then at an angle, which is manufactured in that way, so the top flange clamps down on any thickness of slate, from a 5/6mm general slate to 12/13mm natural slate. 
  3. To open the external face of the slate verge, a temporary batten is placed between the batten courses, which is pushed against the inner face of the slate verge, and nailed in place. This opens the profile of the verge to a vertical position.
  4. The slate are fixed in place in the usual manner, with the outer edge of the slate fixed against the internal edge of the verge. This will hold the verge in the vertical position, and continue this procedure in the normal manner up the verge of the roof. 
  5. The Continuous Slate Dry Verge achieves a professional finish. This will be similar for any slate being used. The completed roof gives complete continuous cover against water penetration, and added strength from wind damage by securing end slates firmly. 

accessories

  • Continuous Dry Verge R Profile Black

    Continuous Dry Verge R Profile

    Compatible with Flat, High and Low Profiled tiles

    View product
  • Continuous Dry Verge S Profile White

    Continuous Dry Verge S Profile

    Compatible with interlocking slates

    View product
  • Continuous Dry Verge Straight Connector R Profile Black

    Continuous Dry Verge Straight Connector R Profile

    Connector for use with Corovent CDV Continuous Dry Verge R Profile

    View product
  • Continuous Dry Verge Straight Connector S Profile Black

    Continuous Dry Verge Straight Connector S Profile

    Connector for use with Corovent CDV Continuous Dry Verge S Profile

    View product
Open/close panel Customer service

Get in touch

Contact our customer service team
*
*
*
*
 
Captcha